1. Duyuruyu Kapat

Yardım | Kali Linux'da Nasıl Driver Yükleyeceğiz

'Ağ araçları' forumunda NsLion tarafından 11 Ocak 2018 tarihinde açılan konu

  1. NsLion

    NsLion New Member

    Katılım:
    1 Nisan 2015
    Mesaj:
    2
    Beğeniler:
    0
    Merhaba arkadaşlar, kali linux kullanıyorum hem kendi wireless imi test etmek için hem de linux kullanmayı sevdiğimden böyle kullanıyorum arada bir fakat laptop ın ağ kartını görmüyor linux. Benim harici wifi adaptörüm var ve bu adaptörün driverlarını indirdim ancak linuxta nasıl yükleyeceğim bilemiyorum birkaç şey denedim fakat terminalde persmission tarzı yetki mesajları / hataları aldım bir türlü yükleyemedim. Aşağıda resimler de var yardımcı olursanız sevinirim.

    Teşekkürler.

    Görüntü 1
    https://i.hizliresim.com/p6v7Ra.png

    Görüntü 2
    https://i.hizliresim.com/NZYy5X.png

    read me dosyası içeriği :

    Release Date: 2006-02-09, ver 1.2
    RTL8187 Linux driver version 1.2

    --This driver supports RealTek RTL8187 Wireless LAN driver for
    Fedora Core 2/3/4/5, Debian 3.1, Mandrake 10.2/Mandriva 2006,
    SUSE 9.3/10.1/10.2, Gentoo 3.1, etc.
    - Support Client mode for either infrastructure or adhoc mode
    - Support WEP and WPAPSK connection

    < Component >
    The driver is composed of several parts:
    1. Module source code
    stack.tar.gz
    drv.tar.gz

    2. Script ot build the modules
    makedrv

    3. Script to load/unload modules
    wlan0up
    wlan0down

    4. Script and configuration for DHCP
    wlan0dhcp
    ifcfg-wlan0
    4. Supplicant source code:
    wpa_supplicant-0.4.9.tar.gz

    5. Example of supplicant configuration file:
    wpa1.conf

    < Installation >
    Runing the scripts can finish all operations of building up modules
    from the source code and start the nic.
    1. Build up the drivers from the source code
    ./makedrv

    2. load the driver module to kernel and start up nic
    ./wlan0up

    < Set wireless lan MIBs >
    This driver uses Wireless Extension as an interface allowing you to set
    Wireless LAN specific parameters.

    Current driver supports "iwlist" to show the device status of nic
    iwlist wlan0 [parameters]
    where
    parameter explaination [parameters]
    ----------------------- -------------
    Show available chan and freq freq / channel
    Show and Scan BSS and IBSS scan[ning]
    Show supported bit-rate rate / bit[rate]
    Show Power Management mode power

    For example:
    iwlist wlan0 channel
    iwlist wlan0 scan
    iwlist wlan0 rate
    iwlist wlan0 power

    Driver also supports "iwconfig", manipulate driver private ioctls, to set
    MIBs.

    iwconfig wlan0 [parameters] [val]
    where
    parameter explaination [parameters] [val] constraints
    ----------------------- ------------- ------------------
    Connect to AP by address ap [mac_addr]
    Set the essid, join (I)BSS essid [essid]
    Set operation mode mode {Managed|Ad-hoc}
    Set keys and security mode key/enc[ryption] {N|open|restricted|off}

    For example:
    iwconfig wlan0 ap XX:XX:XX:XX:XX:XX
    iwconfig wlan0 essid "ap_name"
    iwconfig wlan0 mode Ad-hoc
    iwconfig wlan0 mode essid "name" mode Ad-hoc
    iwconfig wlan0 key 0123456789 [2] open
    iwconfig wlan0 key off
    iwconfig wlan0 key restricted [3] 0123456789

    < Getting IP address >
    After start up the nic, the network needs to obtain an IP address before
    transmit/receive data.
    This can be done by setting the static IP via "ifconfig wlan0 IP_ADDRESS"
    command, or using DHCP.

    If using DHCP, setting steps is as below:
    (1)connect to an AP via "iwconfig" settings
    iwconfig wlan0 essid [name] or
    iwconfig wlan0 ap XX:XX:XX:XX:XX:XX

    (2)run the script which run the dhclient
    ./wlan0dhcp
    or
    dhcpcd wlan0
    (Some network admins require that you use the
    hostname and domainname provided by the DHCP server.
    In that case, use
    dhcpcd -HD wlan0)

    < WPAPSK >
    WPA_SUPPLICANT help the network to communicate under the protection of WPAPSK
    mechanism

    (1)Unpack source code of WPA supplicant:
    tar -zxvf wpa_supplicant-0.4.9.tar.gz
    cd wpa_supplicant-0.4.9

    (2)Create .config file:
    cp defconfig .config

    (3)Edit .config file, uncomment the following line:
    #CONFIG_DRIVER_IPW=y.

    (4)Build WPA supplicant:
    make
    If make error for lack of <include/md5.h>, install the openssl lib(two ways):
    1. Install the openssl lib from corresponding installation disc:
    Fedora Core 2/3/4/5(openssl-0.9.71x-xx), Mandrake10.2/Mandriva10.2(openssl-0.9.7x-xmdk),
    Debian 3.1(libssl-dev), Suse 9.3/10.0/10.1(openssl_devl), Gentoo(dev-libs/openssl), etc.
    2. Download the openssl open source package from www.openssl.org, build and install it.

    (5)Edit wpa_supplicant.conf to set up SSID and its passphrase.
    For example, the following setting in "wpa1.conf" means SSID
    to join is "BufAG54_Ch6" and its passphrase is "87654321".
    network={
    ssid="BufAG54_Ch6"
    proto=WPA
    key_mgmt=WPA-PSK
    pairwise=CCMP TKIP
    group=CCMP TKIP WEP104 WEP40
    psk="87654321"
    priority=2
    }

    (6)Execute WPA supplicant (Assume 8187 and related modules had been
    loaded):
    ./wpa_supplicant -D ipw -c wpa1.conf -i wlan0 &
     
  2. tekroot

    tekroot Well-Known Member

    Katılım:
    11 Ekim 2016
    Mesaj:
    514
    Beğeniler:
    56
    Cinsiyet:
    Erkek
    Meslek:
    programlama teknik yazılım bilgisayar elektronik
    Şehir:
    unknown
    ilk bu depolari ekleyecen sources.list e ac icini komple sil asagidaki depolari icine at
    kaydet guncelleme yaptikdan sonra bak hatan varmi yokmu
    leafpad /etc/apt/sources.list

    deb http://http.kali.org/kali kali-rolling main contrib non-free
    # For source package access, uncomment the following line
    # deb-src http://http.kali.org/kali kali-rolling main contrib non-free

    sonrada kod
    apt-get update
    apt-get dist-upgrade
     
  3. NsLion

    NsLion New Member

    Katılım:
    1 Nisan 2015
    Mesaj:
    2
    Beğeniler:
    0
    Hocam apt-get komutunu girince sanırım kali.org a gidicek terminal. benim bilgisayarımda internet yok. Terminalde apt-get update komutunu girince aldığım hata aşağıdaki gibi.

    https://i.hizliresim.com/lOzBmp.png
     
  4. tekroot

    tekroot Well-Known Member

    Katılım:
    11 Ekim 2016
    Mesaj:
    514
    Beğeniler:
    56
    Cinsiyet:
    Erkek
    Meslek:
    programlama teknik yazılım bilgisayar elektronik
    Şehir:
    unknown
    kabloyla eternet den baglan bence ve sana yukarda dediklerimi aynen yapki eksiklerin giderilsin yoksa ilerleme olmaz sende
    ona gore harfien yapman gerek
     

Bu Sayfayı Paylaş

Share